Видео

Is it cheaper and faster to wear hearing protection? Any way great work.

I built one of these when my son was 5. He used that thing EVERY DAY he came over for the next 2 years. Such good times.

What is that joint called? 5:03

That tie rod guide is expensive.. ace hardware and others 30 plus dollars

Quiero una maquina grande

Very good

Маховик всё таки нужен для такого агрегата, движку будет легче, инерция сила

Now that's a cheater bar.... 😂

Excellent work

Mai visto un silenziatore in lana di roccia?

remove center pipe, fill your silencer with fine steel wool leaving a center hole same size as the exhoust port area.

Parabéns!

Nice job

Se oye igualito pero más afinado

Several of us want to know how much quieter our ... weed eater, yea, will be sir.

Looks better than the drawing 😂

Very sweet design! Works like a champ. Thank you for sharing the "How To" in such detail. Really like that it's a recovered washing machine motor. :)

As a 2-stroke lover I can hear the difference, but it is more scientific if tested with a sound meter

Can you make one for me for my .30 caliber exhaust?

I have a question . Will the high temperatures be transferred from the support blade that is screwed to the handpiece screw and will the plastic parts of the handpiece melt?

لا توجد الياف زجاجية لا يوجد شيء

Go 😂electric. 😂😊

Sounds more like an expansion chamber

я один чую, що результат не вартий зусиль і матеріалу? до того ж, ти задавив двигун - тепер він не розкрутиться до тих обертів, до яких крутився до того, як ти приліпив ту гиригилду. P.S.: відео корисне, як наочний приклад для дітей: на що не варто гаяти свій час і ресурси.

نمبر سند مے

And then the ATF knocked at the door. 😅

Great effort anyway.

You can achieve the same result using a glass bead blast cabinet , it's cheaper , it's quieter , it's FASTER , just need an air compressor , and it wont wear out by the end of the week.

Not good

Nice inexpensive trommel.

Thank you for sharing! Fantastic!

Excellent travail Magnifique 👍

Опа, моя конструкція яку я придумав більше ніж рік тому. На сьогодні вже є багато удосконалень, які дозволяють масштабувати станок до обєму барабана 90-100 літрів. Доречі, пружинна підвіска зроблена не зовсім правильно, і працюватиме відповідно не так добре

Понравилась твоя печурка, благодарю за общий принцип устройства, я себе почти такую же замастырю. С меня лайк и подписка.

Sorry but the 3 minute totally Irrelevant add before vid started, had me moving on.

Nice work with the manufacture of your new deburr and derust tool,, what as the running time of when you put the material in the main drum. I really enjoyed watching your methods of working, have a good day. Phil

Keren sekali 👍

Is it me... or was it not quieter like.. at all..?

Большая часть массы удерживается руками :(

Wood you be able Make one for me I'll pay you I have gas cylinder as well

How do you turn it off if it still has oil?

How did you pull the 4 rods so easily?

Use $10k to $20k of tools (plasma cutter, welder, bandsaw, etc), $500 of labor time, and make a $90 BBQ... Yeah... I'll get right on that...

Nice work

Пушка

...гарна робота. Дякую, що наглядно показали різницю між тим як було і як стало. Усім Добра, Миру і Надхнення! 💙💛

If I only had a $25,000 in shop equipment so I too could build a $550 chipper…

Ist der Motor nicht viel zu schwach?

The best

Ага, и токарник тоже из rust